Advanced Specialty Gas Equipment

Series 150

150 MM, Two Tube Gas Blenders

Two Tube Gas Blender with Optional BaseplateSeries 150 Two Tube Gas Blenders provide a simplified method of metering and blending two different gases into a homogeneous, two component mixture. The blender consists of two Series 150 Flowmeter Tubes, each with separate inlet fittings and metering valves, which control the flow rate of each gas. The ratio of the flow rates of the two gases determines the ratio of the gas mixture. The two gases flow upward through the metering tubes, then down through the mixing tube (located between the two metering tubes)and exiting at the bottom.

Standard Features
  • Two Floats per Tube (Standard) expand range of blender.
  • Ribbed Flow Tubes stabilize floats and improve accuracy and readability.
  • Metal Mixing Tube ensures homogeneous mixing while providing a common outlet port for the gas mixture.
  • Wide Tube Selection allows gases to be blended in a variety of ratios.
  • Linear Scale (10-150 mm) allows each blender to be used with a variety of gases via calibration charts.
  • Threaded Fittings with Locking Nuts permit front panel mounting.
  • Unique Valve Design allows bubble-tight shutoff.
Optional Features
  • Baseplate with Leveling Screws permits bench use.
  • Inlet Filters trap foreign matter, extend flowmeter life and reduce maintenance.
  • High Accuracy Valves with Non-Rotating Stems (NRS) allow very fine adjustments to flow settings.
  • Individual Calibration provides ± 1% of full scale accuracy (±2% on tube No.1).

Maximum Operating Pressure and
  Temperature: 200 psig at 250°F

Minimum Operating Temperature: 32°F

Accuracy: ± 5% of full scale from 10% to
  100% of range (each tube). Optional
  ± 1% of full scale calibration is

  Within 0.5% of full scale (each tube)

Tube Graduations: Millimeters (0-150)

Scale Length: 150 mm

Inlet and Outlet Connections:
   1/8" NPT female (2 inlets, 1 outlet)

Approximate Weight: 2 lbs

Materials of Construction
Tubes: Borosilicate Glass with float stops of PTFE
Mixing Tube: Type 316 Stainless Steel
Floats: Borosilicate Glass and Type 316 
   Stainless Steel are standard.
   Other float materials are available

End Blocks
Inlet/Outlet Adaptors
Side Plates: Aluminum
Back Plate: White Plastic
Front Plate: Clear Plastic
Seals and Packing: Viton®
   (other materials available on special order)
Valve: FM4621: Chrome-Plated Brass
   All Others: Type 316 Stainless Steel

Optional Equipment

Equipment Part No.
Baseplate FM4702
Inlet Filter, 2 micron (2 required)  
  Aluminum FM4741
  Type 316 Stainless Steel FM4746
Floats* (see Optional Equipment Table)  
± 1% Full Scale Calibration* * (one tube, both floats) CC100
* Tubes are supplied standard with borosilicate glass and stainless steel floats. As an option, the glass float may be replaced by sapphire; the stainless steel float may be replaced by either carboloy or tantalum.
* * Specify gas, temperature and pressure when ordering a ±1% calibration. A calibration should be ordered for each of the two tubes. Please note the accuracy for tube No.1 is ±2%.
Table I
Part No. Configuration End Blocks Material Inlet/Outlet
Adaptor Material
FM-4620-( ) With Standard
Metering Valves
Aluminum Aluminum
FM-4621-( ) With High Accuracy
(NRS) Metering Valves
Aluminum Aluminum
FM-4630-( ) With Standard
Metering Valves
316 Stn. Stl. 316 Stn. Stl.
FM-4631-( ) With High Accuracy
(NRS) Metering Valves
316 Stn. Stl. 316 Stn. Stl.
Where "( )" is indicated above, complete the part number by inserting the required tube numbers in the order in which they are to be installed. Select tubes from Tube Selection. Example: FM4620-12, tube no. 1 will be on the left and tube no. 2 on the right. Order by complete part number.
澳洲幸运5计划5码一期 澳洲10开奖视频直播 澳洲10下载 秒速赛车开奖号码